This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
welcome [2017/06/01 16:16] alex [Firmware upgrade] |
welcome [2024/02/27 20:02] 192.168.1.23 [Converting from German to International firmware] |
||
---|---|---|---|
Line 2923: | Line 2923: | ||
2). After the above procedure, it's recommended to first start the tftp on the server before starting the tftp transfer procedure at the bullet-m. | 2). After the above procedure, it's recommended to first start the tftp on the server before starting the tftp transfer procedure at the bullet-m. | ||
+ | |||
+ | ===Further annoying issues as of October 2017== | ||
+ | |||
+ | 1). to avoid any networking locking issues it's better to connect the device on a fast 100Mbit switch. | ||
+ | |||
+ | 2). start the tftp (I use atftp) | ||
+ | |||
+ | 3). cold reboot the Bullet-M | ||
+ | |||
+ | 4). either hold the reset for 10 seconds and then release it or start the urescue from the U-boot menu on the serial console. | ||
====== bullet 5 Openwrt ====== | ====== bullet 5 Openwrt ====== | ||
Line 3238: | Line 3248: | ||
* setup dnsmasq on a linux system (liveCD or liveUSB is fine too, check [[http:// | * setup dnsmasq on a linux system (liveCD or liveUSB is fine too, check [[http:// | ||
* select from bootloader to boot from ethernet | * select from bootloader to boot from ethernet | ||
+ | |||
+ | Update (2017): Lede firmware moved from yaffs2 to ubi file-system. | ||
+ | |||
+ | * netboot the device, use [[http:// | ||
+ | * after net_booting wget or scp [[http:// | ||
+ | * finally issue: sysupgrade / | ||
+ | |||
+ | Older instructions: | ||
+ | |||
* netboot the device, use [[http:// | * netboot the device, use [[http:// | ||
* follow the next steps: | * follow the next steps: | ||
Line 3271: | Line 3290: | ||
opkg install quagga-bgpd | opkg install quagga-bgpd | ||
| | ||
+ | ====== rb711 serial pins ====== | ||
+ | {{http:// | ||
+ | |||
+ | |||
====== rb711 flash howto ====== | ====== rb711 flash howto ====== | ||
+ | a full detailed picture of the board [[http:// | ||
Connect ethernet to the RouterBoard device | Connect ethernet to the RouterBoard device | ||
Line 3481: | Line 3505: | ||
* Basic > DHCP -> σεκάρισμα Ethernet Port #4 -> Submit | * Basic > DHCP -> σεκάρισμα Ethernet Port #4 -> Submit | ||
+ | ====== FRITZ!Box WLAN 3370 ====== | ||
+ | ==== Converting from German to International firmware ==== | ||
+ | |||
+ | you will need a linux box & a windows, preferably a win7 box (side by side) | ||
+ | |||
+ | if you are familiar with windows & ftp and are able to find an ftp client with similar features to the lftp under linux, you may well skip the linux box | ||
+ | |||
+ | searching the netland about this, I bumped on the [[https:// | ||
+ | |||
+ | my advice is to go with a linux/lftp box or even use the [[https:// | ||
+ | |||
+ | it's recommended to network connect all the devices through a simple hub | ||
+ | |||
+ | if you have flashed your Fritz with an alternative firmware, you will need to get back to your official firmware using the [[https:// | ||
+ | |||
+ | on the linux box, set a secondary ip 192.168.178.10/ | ||
+ | |||
+ | get lftp if not already installed and issue the following: | ||
+ | lftp | ||
+ | set net:timeout 1; | ||
+ | set net: | ||
+ | set net: | ||
+ | set net: | ||
+ | open 192.168.178.1 | ||
+ | user adam2 adam2 | ||
+ | you may now enter the following command and very quickly power on your Fritz box | ||
+ | quote GETENV firmware_version | ||
+ | | ||
+ | if the result is: | ||
+ | firmware_version avm | ||
+ | that means, your Fritz box is the German version and you may switch it to the intentional one by issuing the following command: | ||
+ | quote SETENV firmware_version avme | ||
+ | that's it ! you have now switched your German Fritz box to an International Fritz box | ||
+ | |||
+ | you can even power off and then power on again your device and without disconnecting your linux lftp, issue the | ||
+ | quote GETENV firmware_version | ||
+ | in-order to confirm that your Fritz returns the international ID | ||
+ | firmware_version avme | ||
+ | you may now use the [[https:// | ||
+ | |||
+ | the above steps, successfully converted my two German Fritz 3370 to the international version. this same procedure may or may not work on your similar but not exact Fritz box | ||
+ | |||
+ | Good Luck | ||
+ | ==== Flashing openwrt ==== | ||
+ | you need [[https:// | ||
+ | |||
+ | remove power from your fritz box and issue the following command (use the appropriate initramfs-kernel for your box): | ||
+ | eva_ramboot.py 192.168.178.1 openwrt-22.03.6-lantiq-xrx200-avm_fritz3370-rev2-micron-initramfs-kernel.bin | ||
+ | power on your fritz box, wait a few minutes and you should be able to log in 192.168.1.1 | ||
+ | |||
+ | you can now download the proper sysupgrade image and finalize your install |